-
「提升门扭簧」垂直提升门弹簧调松紧方法
The Method of Adjusting and Tightening Vertical Lifting Door Spring
工业提升门离不开弹簧系统的平衡作用,不外弹簧平衡系统使用时间长了,也会出现过松或过紧的问题,这时就需要专业技术职员来进行调试处理。
Industrial lifting door can not be separated from the balance function of spring system, but the spring balance system has been used for a long time, there will be too loose or too tight problems, which requires professional and technical staff to debug and deal with.
一般来说,涉及到工业提升门弹簧系统就只有调整松紧的问题了。
Generally speaking, when it comes to the spring system of industrial lifting door, the only problem is to adjust the tightness.
弹簧调松、调紧的方法不同,详细内容如下所示:
Spring loosening and tightening methods are different. Details are as follows:
门业工业门弹簧调紧方法:
Spring tightening method for door industry:
这一调整过程极为复杂,需要两人配合完成。
This adjustment process is extremely complex and needs the cooperation of two people to complete.
「提升门扭簧」垂直提升门弹簧调松紧方法
The Method of Adjusting and Tightening Vertical Lifting Door Spring
操纵时,先用鼎力钳夹住紧簧座四周的轴,然后一人将紧簧杆插入紧簧座内用力向上稳住,另一人松开紧簧座上的两颗方型螺丝后,再将另一紧簧杆插入另一紧簧孔内,两人平均用力向上抬。
During the operation, the axle around the spring seat is clamped with a tripod clamp, then one person inserts the spring rod into the spring seat and forces it upward. The other person loosens the two square screw on the spring seat, then inserts the other spring rod into the hole of the other spring. The two people lift the spring rod upward with average force.
待达到预定的圈数后,再用一个方形螺丝将弹簧锁在轴的键槽内,另一螺丝锁在轴上。
After reaching the predetermined number of circles, a square screw is used to lock the spring in the key groove of the shaft, and another screw is locked on the shaft.
假如弹簧调的过紧,则需要松开重新调整 。
If the spring is overstretched, it needs to be loosened and readjusted.
工业门弹簧调松方法:
Method for adjusting spring loosening of industrial door:
同紧弹簧一样,这一操纵过程也需要两人配合完成。其操纵方法的第一步同上面的弹簧调紧一样。
As with the tight spring, this control process also requires the cooperation of two people to complete. The first step of the control method is the same as the spring tightening above.
此外,在调松弹簧时,为了安全起见,建议大家在原来圈数的基础上每半圈半圈地进行加减,同时每加、减一次,都要停下来试一下,然后判断是否还需要继承增加或减少圈数。
In addition, when adjusting the spring, in order to be safe, it is suggested that we add or subtract every half circle and half circle on the basis of the original number of circles, and at the same time stop and try every addition or subtraction, and then judge whether it is necessary to inherit the increase or decrease of the number of circles.
千万不能一次性几圈几圈地加大或减少提升门弹簧的圈数,否则弹簧过紧,工业门的门体就会冲出轨道。
Must not increase or decrease the number of rings of the lifting door spring several times at a time, otherwise the spring is too tight, the door body of the industrial door will rush out of the track.
「提升门扭簧」垂直提升门弹簧调松紧方法
作者:提升门弹簧 时间:2019/7/17 11:20:18- 工业推拉门配件-购买平移门配件自己做大门 23-03-27
- 工业门配件厂家批发-电动提升门配件 22-11-29
- 工业折叠门-厂房电动折叠门定做 22-09-22
- 工业推拉门配件-平移门吊轮吊轨批发 22-09-01
相关新闻: